Machine Diagnostics

Measure what the machine actually does — vibration, geometry and interpolation, documented against the standard.

What we offer

Why this matters

A machine does not lose its accuracy all at once. It loses it slowly — through bearing wear, thermal cycles, backlash creeping into the drives — and most shops find out when a part fails inspection.

Diagnostics turns that around. We measure the real condition of the machine with calibrated equipment, document it in a protocol written against the standard, and where it can be done, set the compensations on the spot. What you get is not a technician’s opinion but numbers — numbers you can compare with last year and attach to a job.

Measure regularly rather than only when something is wrong. A single measurement tells you whether the machine passes. Only a series of measurements over time shows the trend — and the trend is what lets you plan a repair into a shutdown instead of into a breakdown.

Machine Diagnostics FAQ

Machine Quick-Check

View service

What can vibration diagnostics actually tell apart?

The frequency spectrum separates causes that all feel the same from outside. Rotational frequency points to imbalance or misalignment, gear-mesh frequency to the gearing, and bearing frequencies with their sidebands to a specific bearing. That is the difference between "the spindle vibrates" and "this bearing is on its way out".

Does the machine have to be stopped for the whole day?

No — the check takes five hours, so it fits inside one shift. That is the point of Quick-Check: enough measurement to know where you stand, without the machine standing still for a full geometry survey.

What is the difference between Quick-Check and the Interpolation check?

Quick-Check is the fast overview — spindle condition plus a ball bar test in five hours. The Interpolation check is the full survey: laser interferometry of the linear axes and ball bar testing in all three planes, six to eight hours, with a protocol to VDI or ISO. Quick-Check often leads to it.

Why measure once a year rather than when there is a problem?

A single measurement tells you whether the machine passes today. A series of them shows the trend — and the trend is what lets you schedule a repair into a planned shutdown instead of discovering it through a scrapped part.

Interpolation Check

View service

Why does the measurement need stable conditions in the shop?

A laser interferometer measures to a resolution where the temperature of the air and of the machine itself moves the result. Measuring next to a machine that is heating up, or during a shift change with the doors open, produces numbers that describe the weather rather than the machine. Stable conditions are what make the protocol worth having.

How should we prepare for the measurement?

The machine should be at a settled temperature, the table clear and accessible, and machines immediately around it ideally not running heavy cuts during the measurement. We agree the details in advance — the more stable the conditions, the more usable the protocol.

Can we hand the protocol to our own customer?

That is what it is for. The protocol is written to VDI or ISO standards, so it is comparable and defensible rather than an internal note. Customers in regulated or safety-critical work usually ask for exactly this.

Should this be combined with the Geometry check?

Usually yes. Geometry and motion accuracy are related and measuring them separately rarely makes sense — a geometry error shows up in the interpolation result and vice versa.

Geometry Check

View service

Which standards do you measure to?

Unless we agree otherwise, the current international ISO standards: ISO 230-1 for geometric accuracy under no-load or quasi-static conditions, ISO 10791-1 for machining centres with a horizontal spindle, and ISO 3070-3 for boring and milling machines with a movable column and movable table.

Do you only measure, or also correct?

Both. Adjustment of the geometry is part of the service. A measurement that only tells you the machine is out leaves you with the same problem you started with.

When is a geometry check worth doing?

When parts start drifting out of tolerance without an obvious cause, after the machine has been moved or re-levelled, and as part of a regular measurement interval so you have something to compare against.

Why combine it with the Interpolation Check?

Because they measure two aspects of the same thing. A geometric deviation shows up as a distortion in the interpolation result, and a drive that is out of tune can look like a geometry error. Measured together, each explains the other.

Not sure which one you need?

Tell us the machine and its serial number — we look up the configuration and answer specifically rather than generally.

Technical support: technicalsupport@fermat.cz

Service: service@fermat.cz

Monday to Friday, 7:30–15:00 CET/CEST