Freshly machined precision steel components on a workshop bench — job-shop machining

General Machining

Horizontal boring and milling machines for the multi-material, mixed-batch demands of contract machining and job-shop operations.

The Challenge of General Machining Machining

Contract machining is the hardest segment to buy a machine for, not because of any single technical challenge but because every week brings a different one. A one-off prototype housing on Monday, a mid-volume run of steel gearbox bodies on Wednesday, an urgent pump casing for a customer whose line is down on Friday. The machine has to be good at all of it, because none of it repeats.

That reality puts the value in three places. Versatility, because a machine that cuts cast iron well but fights stainless loses money on every off-spec batch. Setup time, because it comes straight out of billable hours — every re-clamping is time nobody pays for, and on a one-off there is no second part to amortise it against. And uptime, because a job shop that misses a promised date loses the next order too.

FERMAT horizontal boring and milling centres are built around that: a heavy cast-iron structure that takes interrupted cuts in weldments without chatter, a spindle sized for boring and milling in the same clamping rather than one at the expense of the other, and rotary tables and universal heads that let a part be turned to the tool instead of being unclamped and re-set. Pallet changers cut the changeover on repeat batches, and the same machine takes prototypes, subcontract runs, MRO work and the shop’s own fixtures and tooling.

Why FERMAT for General Machining

Engineering decisions baked into every machine that change the economics of general machining production.

Built for mixed work

One platform for cast iron, steel, stainless and weldments — no batch has to wait for the right machine to be free.

Fewer setups per part

Rotary table and universal heads bring the part to the tool, so bores and faces on several sides are cut in one clamping.

Takes interrupted cuts

Heavy cast-iron construction absorbs the impacts of weldment and plate machining without chatter marking the surface.

New or pre-owned entry

The same platform is available as a new build or a used machine, so a shop can start smaller and step up as the order book grows.

Recommended Machines

Machine types that suit general machining parts.

All categories

General Machining FAQ

Engineering and procurement questions about general machining machining.

Which FERMAT machine suits a general job shop?

For mixed subcontract work the table-type machines are the usual starting point — the workpiece sits on the rotary table and the machine works around it, which suits parts that arrive in every shape. Where parts get too large or heavy to put on a table, a floor-type machine takes over. The deciding questions are the heaviest part you expect to clamp and the longest bore you need to reach.

Can one machine handle different materials?

Yes. A two-stage gearbox gives high torque at low speed for boring cast iron and steel, and higher speed for lighter milling, so the same spindle covers both ends of the range. Material changes are a matter of cutting data and tooling rather than a different machine.

How much can be machined in a single setup?

A rotary table lets the part be indexed to the tool, so bores and faces on several sides are cut from one clamping and one datum. An angular or universal milling head reaches faces the spindle cannot address directly. That matters most on one-off work, where every re-clamping is setup time nobody is paying for.

How fast can the machine be changed over between batches?

On repeat work an automatic pallet changer takes most of the changeover off the machine: the next part is clamped on the second pallet while the current one is still being cut. On one-off work the gain comes instead from the reduced number of setups per part.

Is the CNC control difficult for a shop-floor operator?

FERMAT machines are available with HEIDENHAIN, SIEMENS, FANUC or FERMAT's own EASYCRAFT control. HEIDENHAIN (Klartext), SIEMENS (ShopMill / ShopTurn) and EASYCRAFT (graphical cycles, no ISO code) let an operator program at the machine; FANUC is programmed in G-code, with on-screen G-code guidance. Complex parts still come from CAM.

Looking for a general machining machining partner?

Our engineers spec the right configuration for your specific application. We reply within 24 hours.

Browse Machines